Water purification information

Work flow and work requirements of softened water equipment

Views : 71374
Update time : 2021-09-26 11:53:54
(1) Work flow of softened water equipment
Work (sometimes called water production, the same below), backwashing, salt absorption (regeneration), slow flushing (replacement), and fast flushing. All the processes of different softened water equipment are very similar, but due to the actual process or the need for control, there may be some additional processes. Any water softening equipment based on sodium ion exchange is developed on the basis of these five processes (among which, fully automatic water softening equipment will increase the brine reinjection process).

Backwashing: After working for a period of time, the equipment will intercept a lot of dirt brought by the raw water on the top of the resin. After the dirt is removed, the ion exchange resin can be completely exposed and the regeneration effect can be guaranteed. The backwashing process is that water washes in from the bottom of the resin and flows out from the top, so that the dirt intercepted by the top can be washed away. This process generally takes about 5-15 minutes. Salt absorption (regeneration): the process of injecting salt water into the resin tank. The traditional equipment uses a salt pump to inject the salt water, and the fully automatic equipment uses a dedicated built-in ejector to suck the salt water (as long as the inlet water has a certain pressure) . In the actual working process, the regeneration effect of salt water flowing through the resin at a slower speed is better than that of simply soaking the resin with salt water. Therefore, the softened water equipment is regenerated by the method of slowly flowing salt water through the resin. This process generally requires 30 About minutes, the actual time is affected by the amount of salt used. Slow flushing (replacement): After the salt water flows through the resin, the process of slowly flushing all the salt in the resin with raw water at the same flow rate is called slow flushing, because there are still a large number of functional groups in the flushing process. Calcium and magnesium ions are exchanged by sodium ions. According to actual experience, this process is the main process of regeneration, so many people call this process replacement. This process is generally the same as the salt absorption time, which is about 30 minutes. Quick flushing: In order to thoroughly flush the remaining salt, the resin should be flushed with raw water at a flow rate close to the actual work. The final effluent of this process should be soft water that meets the standard. Under normal circumstances, the fast flushing process is 5-15 minutes.
 

(2) Technical indicators and work requirements of softened water equipment:

Inlet water pressure: 0.18-0.6Mpa

Working temperature: 1-55℃ Source water hardness: <8mmol/L

Operation mode: automatic/manual water hardness: ≤0.03mmol/L

Regeneration agent: NaCL Regeneration method: downstream/countercurrent

Exchanger: 001*7 strong acid ion exchange resin

Control method: time/flow power supply: 220V/50Hz
Related News
Read More >>
Should we install a direct drinking water purifier or not? Should we install a direct drinking water purifier or not?
Sep .19.2024
     At this stage, people's main source of water is tap water, the most direct method of drinking water is a water dispenser, but at present, tap water pollution is very serious, most families have long been installed in the household direct drinking water purifier to provide clean and safe drinking water, but many people are still on the direct drinking water purifier products there are misunderstandings, holding a fluke in the thought of my home in the end do I need to install a water purifier it? In fact, the most professional answer is: there is no need! The health benefits is the biggest demand!
Commercial / Household water purifier (direct water dispenser) fault book Commercial / Household water purifier (direct water dispenser) fault book
Sep .19.2024
The amount of water in the water purifier is small, the water purifier does not produce water, the noise of the water purifier has become louder, the water purifier ....... Susan summarized 25 common fault problems of water purifier for you, hand in hand to teach you how to troubleshoot, so you can easily deal with the water purifier, enjoy good quality water.
The necessity of regular cleaning of reverse osmosis membranes The necessity of regular cleaning of reverse osmosis membranes
Sep .18.2024
In the long-term membrane separation process, 4040 reverse osmosis membrane water permeability will decline with the growth of operating time, this phenomenon occurs because of membrane contamination problems. It can be seen that it is necessary to carry out regular cleaning of the membrane element system, so that the 4040 reverse osmosis membrane surface or membrane pore contamination removal, to restore water permeability and extend the membrane life of the purpose.
Application of water purifier in public places: guarding every drop of healthy water source Application of water purifier in public places: guarding every drop of healthy water source
Sep .14.2024
In today's society, with people's pursuit of a healthy life and increasing concern for environmental quality, water purifiers, as an effective water treatment equipment, is gradually playing an increasingly important role in public places. Schools, hospitals, offices and other public places, due to the high flow of people, high demand for water, water quality requirements are more stringent. Therefore, the application of water purifiers in these places is particularly important.